Metso gyratory crusher parts designed for Superior™ (TS & MK-II/III), C-G, and legacy Allis-Chalmers gyratory crusher models. They cover both major assemblies and routine-replacement parts to keep primary crushers running at full capacity and safety.
1. Structural / Major Assemblies
Mainshaft assemblies – forged shaft, head, eyebolt
Spider – spider casting, spider arm shield, spider rim liner, spider cap
Top shell & bottom shell – cast topshell, narrow arm liners, side liners
MPS / Hydroset cylinder – cylinder casting, upper & lower bushings, piston
2. Eccentric & Drive Components
Eccentric assembly – eccentric forging, bronze eccentric bushing, wearing ring
Pinion shaft & housing – spiral-bevel pinion, pinion shaft, bearings, seal plates, vibration sensors
Countershaft & motor – countershaft box, sheaves, belts, guards
3. Liners & Crushing Surfaces
Cone Crusher Mantle Liner – one-piece, partially corrugated
Concave segments – upper, middle, lower tiers, key & key-riser systems
Backing compounds & epoxy for secure liner seating
4. Bushings, Bearings & Seals
Bottom-shell bushings
Spider bushings & sleeves
Dust-seal rings, oil-seal rings, labyrinth seals
5. Hydraulics, Lube & Automation
Hydroset control valves, MPS pumps, accumulators
Lube-pump motors, filters, heat exchangers, level & temperature sensors
All parts are OEM-manufactured to original drawings, interchangeable, and available with upgrade material for longer using life. Which popular parts in ONA?
| 1 | 17-203-344-001 | SNAP RING | SG4265 |
| 2 | 17-203-344-002 | OUTBOARD BEARING | SG4265 |
| 3 | 17-203-344-003 | SEAL | SG4265 |
| 4 | 17-203-344-004 | SHAFT END COVER | SG4265 |
| 5 | 17-203-344-005 | PLUG | SG4265 |
| 6 | 17-203-344-006 | BUSHINGS | SG4265 |
| 7 | 17-203-344-007 | CHANNEL SEAL | SG4265 |
| 8 | 17-203-344-008 | THRUST PLATES | SG4265 |
| 9 | 17-203-344-009 | INTERGRAL DRIVE SHAFT AND GEAR SET | SG4265 |
| 10 | 17-203-344-010 | GASKET SEAL | SG4265 |
| 11 | 17-203-344-011 | UUWEL PINS | SG4265 |
| 12 | 17-203-344-012 | GEAR HDUSING | SG4265 |
| 13 | 17-203-344-013 | BEARING CARRIER | SG4265 |
| 14 | 17-203-344-014 | CONNECTING SHAF T | SG4265 |
| 15 | 17-203-344-015 | MATCHED GEAR SET | SG4265 |
| 16 | 17-203-344-016 | GEAR HOUSING | SG4265 |
| 17 | 17-203-344-017 | PORT END COVER | SG4265 |
| 18 | 7-203-344-018 | STUDS OR CAPSCREWS | SG4265 |
| 19 | 17-203-344-019 | WASHERS | SG4265 |
| 20 | 17-203-344-020 | NUTS | SG4265 |
| 21 | 17-502-274-402 | SECTIONAL ELEVATION | SG4265 |
| 22 | 17-502-197-401 | LOWER SECTION ASSEMBLY PIX | SG4265 |
| 23 | 17-502-132-501 | BOTTOMSHELL W/HUB LINER | SG4265 |
| 24 | 07-349-665-001 | NARROW ARM LINER FLARED | SG4265 |
| 25 | 17-200-630-001 | PINIONSHAFT ARM LINER LEFT HAND | SG4265 |
| 26 | 17-200-629-001 | PINIONSHAFT ARM LINER RIGHT HAND | SG4265 |
| 27 | 60-454-460-030 | BAR | SG4265 |
| 28 | 60-454-520-015 | BAR | SG4265 |
| 29 | 17-303-663-801 | NAMEPLATES AND WARNING ASSEMBLY | SG4265 |
| 30 | 17-303-663-401 | NAMEPLATE AND WARNING PIX | SG4265 |
| 31 | 17-107-457-806 | NAMEPLATE -SUPERIOR | SG4265 |
| 32 | 17-303-751-001 | METSO MARK | SG4265 |
| 33 | 17-303-752-001 | SUPERIOR TRADEMARK | SG4265 |
| 34 | 17-203-351-001 | ACCEN STRIPE | SG4265 |
| 35 | 00-615-613-149 | DRIVE SCREW | SG4265 |
| 36 | 17-107-586-001 | PATENT PLATE | SG4265 |
| 37 | 07-250-010-001 | BOTTOMSHELL BUSH | SG4265 |
| 38 | 07-246-237-001 | BOTTOMSHELL BUSHING KEY | SG4265 |
| 39 | 17-202-702-501 | LUBE INLET PIPE | SG4265 |
| 40 | 17-104-885-002 | BRAIDED PACKING | SG4265 |
| 41 | 17-203-226-501 | PACKING GLAND ASSEMBLY | SG4265 |
| 42 | 00-611-322-474 | CAPSCREW | SG4265 |
| 43 | 00-651-001-214 | WASHER | SG4265 |
| 44 | 00-671-171-523 | SPLIT PIN HOLLOW | SG4265 |
| 45 | 17-200-306-501 | BOTTOMSHELL HUB LINER UPPER | SG4265 |
| 46 | 17-200-308-501 | BOTTOMSHELL HUB LINER UPPER | SG4265 |
| 47 | 17-200-307-501 | BOTTOMSHELL HUB LINER UPPER | SG4265 |
| 48 | 17-100-831-001 | BOTTOMSHELL HUB LINER LOWER | SG4265 |
| 49 | 17-100-832-001 | BOTTOMSHELL HUB LINER UPPER | SG4265 |
| 50 | 17-100-831-001 | BOTTOMSHELL HUB LINER LOWER | SG4265 |
| 51 | 17-402-181-401 | SIDE LINER INSTALLATION PIX | SG4265 |
| 52 | 17-400-969-801 | BOTTOMSHELL SIDE LINER ASSEMBLY | SG4265 |
| 53 | 17-400-969-501 | BS LINER PINIONSHAFT LEFT HAND | SG4265 |
| 54 | 17-400-969-502 | BS LINER PINIONSHAFT RIGHT HAND | SG4265 |
| 55 | 17-400-969-508 | BS LINER OPPOSITE PINIONSHAFT LEFT HAND | SG4265 |
| 56 | 17-400-969-507 | BS LINER OPPOSITE PINIONSHAFT LEFT HAND | SG4265 |
| 57 | 17-400-969-503 | BS LINER INTERMEDIATE LEFT HAND | SG4265 |
| 58 | 17-400-969-504 | BS LINER INTERMEDIATE RIGHT HAND | SG4265 |
| 59 | 17-400-969-505 | BS LINER NARROW ARM RIGHT HAND | SG4265 |
| 60 | 17-400-969-506 | BS LINER NARROW ARM LEFT HAND | SG4265 |
| 61 | 17-201-116-002 | SIDE LINER WEDGE -PLAIN | SG4265 |
| 62 | 17-201-116-001 | SIDE LINER WEDGE -SLOTTED | SG4265 |
| 63 | 17-107-630-001 | CAPSCREW | SG4265 |
| 64 | 00-631-001-120 | HEX NUT | SG4265 |
| 65 | 00-631-141-120 | HEX JAMNUT | SG4265 |
| 66 | 00-651-001-584 | WASHER | SG4265 |
| 67 | 17-202-773-001 | DUST COLLAR | SG4265 |
| 68 | 00-615-142-728 | CAPSCREW | SG4265 |
| 69 | 00-651-016-988 | WASHER | SG4265 |
| 70 | 00-655-009-052 | LOCKWASHER | SG4265 |
| 71 | 00-671-171-523 | SPLIT PIN HOLLOW | SG4265 |
| 72 | 17-203-277-001 | UPPER COUNTERWEIGHT SPLASH RING | SG4265 |
| 73 | 00-615-086-546 | CAPSCREW FLAT HEAD | SG4265 |
| 74 | 17-201-512-001 | DUST COLLAR GASKET | SG4265 |
| 75 | 17-300-396-001 | STUD | SG4265 |
| 76 | 00-631-001-116 | HEX NUT | SG4265 |
| 77 | 00-651-001-490 | WASHER | SG4265 |
| 78 | 00-631-141-116 | HEX JAMNUT | SG4265 |
| 79 | 07-146-694-008 | BOLT SQ.HD | SG4265 |
| 80 | 00-631-041-148 | HEAVY HE NUT | SG4265 |
| 81 | 00-631-161-148 | HEAVY HEX JAMNUT | SG4265 |
| 82 | 17-202-783-501 | AIR INLE CONNECTOR ASSEMBLY | SG4265 |
| 83 | 17-402-791-401 | ECCENTRI ASSEMBLY PIX | SG4265 |
| 84 | 17-402-789-506 | ECCENTRI ASSEMBLY | SG4265 |
| 85 | 17-302-945-001 | ECCENTRI MKII | SG4265 |
| 86 | 17-401-227-001 | ECCENTRIC BUSHING | SG4265 |
| 87 | 17-203-275-501 | UPPER COUNTERWEIGHT ASSEMBLY | SG4265 |
| 88 | 00-615-138-658 | CAPSCREW HEX SOCKET NYLOK | SG4265 |
| 89 | 17-402-788-001 | UPPER COUNTERWEIGHT | SG4265 |
| 90 | 00-615-138-561 | CAPSCREW HEX SOCKET NYLOK | SG4265 |
| 91 | 17-303-595-001 | UPPER COUNTERWEIGHT RETAINER RING | SG4265 |
| 92 | 17-302-957-001 | LOWER COUNTERWEIGHT | SG4265 |
| 93 | 00-615-142-669 | CAPSCREW HE SOCKET | SG4265 |
| 94 | 00-651-016-411 | WASHER | SG4265 |
| 95 | 00-671-115-583 | DOWEL PIN | SG4265 |
| 96 | 07-246-281-001 | KEY ECCENTRI BUSHING | SG4265 |
| 97 | 17-302-958-001 | ECCENTRIC GEAR MKII | SG4265 |
| 98 | 07-145-539-001 | KEY,ECCENTRIC GEAR | SG4265 |
| 99 | 00-615-142-611 | CAPSCREW HEX SOCKET | SG4265 |
| 100 | 07-345-013-001 | ECCENTRIC WEARING RING | SG4265 |
| 101 | 17-303-084-001 | ECCENTRIC SUPPOR RING | SG4265 |
| 102 | 00-615-142-724 | CAPSCRE HEX SOCKET | SG4265 |
| 103 | 00-655-009-052 | LOCKWASHER | SG4265 |
| 104 | 17-201-787-055 | O-RING | SG4265 |
| 105 | 17-303-562-503 | MPS CYLINDER W/SHIP COVERS | SG4265 |
| 106 | 17-402-757-401 | MPS CYLINDER INSTALL PIX | SG4265 |
| 107 | 17-501-860-503 | MPS CYLINDER W/POSITION INDICATOR ASM | SG4265 |
| 108 | 17-300-182-501 | MPS CYLINDER | SG4265 |
| 109 | 17-300-396-002 | STUD | SG4265 |
| 110 | 00-631-041-128 | HEAVY HEX NUT | SG4265 |
| 111 | 00-631-161-128 | HEAVY HEX JAMNUT | SG4265 |
| 112 | 17-302-899-001 | MPS CYLINDER BUSHING -LOWER | SG4265 |
| 113 | 07-250-231-501 | MPS CYLINDER BUSHING -UPPER | SG4265 |
| 114 | 00-615-142-651 | CAPSCREW HEX SOCKET | SG4265 |
| 115 | 00-615-138-651 | CAPSCREW HEX SOCKET NYLON | SG4265 |
| 116 | 00-671-171-523 | SPLIT PIN HOLLOW | SG4265 |
| 117 | 00-711-497-016 | PIPE PLUG SQ.HD | SG4265 |
| 118 | 17-201-787-035 | O-RING | SG4265 |
| 119 | 17-402-244-501 | PISTON AND PLUG ASSEMBLY | SG4265 |
| 120 | 17-202-759-001 | PISTON PLUG | SG4265 |
| 121 | 00-615-142-613 | CAPSCREW HEX SOCKET | SG4265 |
| 122 | 00-711-533-008 | PIPE PLUG CI | SG4265 |
| 123 | 00-671-117-877 | DOWEL PIN | SG4265 |
| 124 | 17-303-539-501 | PISTON WEAR PLATE ASSEMBLY | SG4265 |
| 125 | 17-104-616-001 | STEP WASHER RETAINER | SG4265 |
| 126 | 00-673-165-300 | RETAINING RING, EXTERNAL | SG4265 |
| 127 | 07-252-540-001 | STEP WASHER | SG4265 |
| 128 | 17-103-679-003 | MPS SEAL W/O FILLER | SG4265 |
| 129 | 17-302-963-001 | CLAMP PLATE | SG4265 |
| 130 | 17-202-782-001 | SEAL RETAINER RING | SG4265 |
| 131 | 00-615-142-468 | CAPSCREW HEX SOCKET | SG4265 |
| 132 | 00-655-009-032 | LOCKWASHER | SG4265 |
| 133 | 17-303-650-001 | HOLDER -MEASURING TUBE | SG4265 |
| 134 | 65-965-027-002 | GASKET-TAPERED | SG4265 |
| 135 | 17-107-498-001 | PLUG,POSITION INDICATOR MEASURING TUBE | SG4265 |
| 136 | 65-751-536-006 | O-RING | SG4265 |
| 137 | 17-203-309-001 | PLUG-MEASURING TUBE | SG4265 |
| 138 | 29300219 | DECAL-RESPIRATOR | SG4265 |
| 139 | 26-205-880-001 | WARNING SIGN -GUARD IN | SG4265 |
| 140 | 26-206-910-001 | WARNING SIGN -LIFTING | SG4265 |
| 141 | 26-206-911-001 | WARNING SIGN -LOCKOUT | SG4265 |
| 142 | 26-206-912-001 | WARNING SIGN -STAND CLEAR | SG4265 |
| 143 | 17-402-218-501 | MPS CYLINDER COVER PLATE ASSEMBLY | SG4265 |
| 144 | 00-751-531-474 | O-RING | SG4265 |
| 145 | 65-615-145-079 | CAPSCREW SOCKET | SG4265 |
| 146 | 17-201-249-003 | BOLT SQ.HEAD | SG4265 |
| 147 | 00-631-041-128 | HEAVY HEX NUT | SG4265 |
| 148 | 00-631-161-128 | HEAVY HEX JAMNUT | SG4265 |
| 149 | 00-711-509-006 | PIPE PLUG | SG4265 |
| 150 | 17-107-495-004 | POSITION TRANSDUCER 400MM WI TUBE | SG4265 |
| 151 | 00-615-142-548 | CAPSCREW HEX SOCKET | SG4265 |
| 152 | 65-655-022-007 | SPRING WASHER | SG4265 |
| 153 | 00-711-087-052 | PIPE BUSHING CI | SG4265 |
| 154 | 65-751-532-026 | O-RING | SG4265 |
| 155 | 17-106-891-002 | MPS SHIPPING COVER PLATE GUARD | SG4265 |
| 156 | 17-107-040-510 | CABLE ASSEMBLY | SG4265 |
| 157 | 17-203-302-001 | POSITION TRANSDUCER ADAPTER | SG4265 |
| 158 | 65-751-532-091 | O-RING | SG4265 |
| 159 | 65-615-146-304 | CAPSCREW SOCKET | SG4265 |
| 160 | 17-402-904-505 | ENGLISH | SG4265 |