Metso gyratory crusher parts designed for Superior™ (TS & MK-II/III), C-G, and legacy Allis-Chalmers gyratory crusher models. They cover both major assemblies and routine-replacement parts to keep primary crushers running at full capacity and safety.

 

1. Structural / Major Assemblies

Mainshaft assemblies – forged shaft, head, eyebolt  

Spider – spider casting, spider arm shield, spider rim liner, spider cap  

Top shell & bottom shell – cast topshell, narrow arm liners, side liners  

MPS / Hydroset cylinder – cylinder casting, upper & lower bushings, piston

 

2. Eccentric & Drive Components

Eccentric assembly – eccentric forging, bronze eccentric bushing, wearing ring  

Pinion shaft & housing – spiral-bevel pinion, pinion shaft, bearings, seal plates, vibration sensors  

Countershaft & motor – countershaft box, sheaves, belts, guards  

 

3. Liners & Crushing Surfaces

Cone Crusher Mantle Liner – one-piece, partially corrugated

Concave segments – upper, middle, lower tiers, key & key-riser systems  

Backing compounds & epoxy for secure liner seating  

 

4. Bushings, Bearings & Seals

Bottom-shell bushings 

Spider bushings & sleeves 

Dust-seal rings, oil-seal rings, labyrinth seals 

 

5. Hydraulics, Lube & Automation

Hydroset control valves, MPS pumps, accumulators 

Lube-pump motors, filters, heat exchangers, level & temperature sensors 

 

All parts are OEM-manufactured to original drawings, interchangeable, and available with upgrade material for longer using life. Which popular parts in ONA?

1	17-203-344-001	SNAP RING	SG4265
2	17-203-344-002	OUTBOARD BEARING	SG4265
3	17-203-344-003	SEAL	SG4265
4	17-203-344-004	SHAFT END COVER	SG4265
5	17-203-344-005	PLUG	SG4265
6	17-203-344-006	BUSHINGS	SG4265
7	17-203-344-007	CHANNEL SEAL	SG4265
8	17-203-344-008	THRUST PLATES	SG4265
9	17-203-344-009	INTERGRAL DRIVE SHAFT AND GEAR SET	SG4265
10	17-203-344-010	GASKET SEAL	SG4265
11	17-203-344-011	UUWEL PINS	SG4265
12	17-203-344-012	GEAR HDUSING	SG4265
13	17-203-344-013	BEARING CARRIER	SG4265
14	17-203-344-014	CONNECTING SHAF T	SG4265
15	17-203-344-015	MATCHED GEAR SET	SG4265
16	17-203-344-016	GEAR HOUSING	SG4265
17	17-203-344-017	PORT END COVER	SG4265
18	7-203-344-018	STUDS OR CAPSCREWS	SG4265
19	17-203-344-019	WASHERS	SG4265
20	17-203-344-020	NUTS	SG4265
21	17-502-274-402	SECTIONAL ELEVATION	SG4265
22	17-502-197-401	LOWER SECTION ASSEMBLY PIX	SG4265
23	17-502-132-501	BOTTOMSHELL W/HUB LINER	SG4265
24	07-349-665-001	NARROW ARM LINER FLARED	SG4265
25	17-200-630-001	PINIONSHAFT ARM LINER LEFT HAND	SG4265
26	17-200-629-001	PINIONSHAFT ARM LINER RIGHT HAND	SG4265
27	60-454-460-030	BAR	SG4265
28	60-454-520-015	BAR	SG4265
29	17-303-663-801	NAMEPLATES AND WARNING ASSEMBLY	SG4265
30	17-303-663-401	NAMEPLATE AND WARNING PIX	SG4265
31	17-107-457-806	NAMEPLATE -SUPERIOR	SG4265
32	17-303-751-001	METSO MARK	SG4265
33	17-303-752-001	SUPERIOR TRADEMARK	SG4265
34	17-203-351-001	ACCEN STRIPE	SG4265
35	00-615-613-149	DRIVE SCREW	SG4265
36	17-107-586-001	PATENT PLATE	SG4265
37	07-250-010-001	BOTTOMSHELL BUSH	SG4265
38	07-246-237-001	BOTTOMSHELL BUSHING KEY	SG4265
39	17-202-702-501	LUBE INLET PIPE	SG4265
40	17-104-885-002	BRAIDED PACKING	SG4265
41	17-203-226-501	PACKING GLAND ASSEMBLY	SG4265
42	00-611-322-474	CAPSCREW	SG4265
43	00-651-001-214	WASHER	SG4265
44	00-671-171-523	SPLIT PIN HOLLOW	SG4265
45	17-200-306-501	BOTTOMSHELL HUB LINER UPPER	SG4265
46	17-200-308-501	BOTTOMSHELL HUB LINER UPPER	SG4265
47	17-200-307-501	BOTTOMSHELL HUB LINER UPPER	SG4265
48	17-100-831-001	BOTTOMSHELL HUB LINER LOWER	SG4265
49	17-100-832-001	BOTTOMSHELL HUB LINER UPPER	SG4265
50	17-100-831-001	BOTTOMSHELL HUB LINER LOWER	SG4265
51	17-402-181-401	SIDE LINER INSTALLATION PIX	SG4265
52	17-400-969-801	BOTTOMSHELL SIDE LINER ASSEMBLY	SG4265
53	17-400-969-501	BS LINER PINIONSHAFT LEFT HAND	SG4265
54	17-400-969-502	BS LINER PINIONSHAFT RIGHT HAND	SG4265
55	17-400-969-508	BS LINER OPPOSITE PINIONSHAFT LEFT HAND	SG4265
56	17-400-969-507	BS LINER OPPOSITE PINIONSHAFT LEFT HAND	SG4265
57	17-400-969-503	BS LINER INTERMEDIATE LEFT HAND	SG4265
58	17-400-969-504	BS LINER INTERMEDIATE RIGHT HAND	SG4265
59	17-400-969-505	BS LINER NARROW ARM RIGHT HAND	SG4265
60	17-400-969-506	BS LINER NARROW ARM LEFT HAND	SG4265
61	17-201-116-002	SIDE LINER WEDGE -PLAIN	SG4265
62	17-201-116-001	SIDE LINER WEDGE -SLOTTED	SG4265
63	17-107-630-001	CAPSCREW	SG4265
64	00-631-001-120	HEX NUT	SG4265
65	00-631-141-120	HEX JAMNUT	SG4265
66	00-651-001-584	WASHER	SG4265
67	17-202-773-001	DUST COLLAR	SG4265
68	00-615-142-728	CAPSCREW	SG4265
69	00-651-016-988	WASHER	SG4265
70	00-655-009-052	LOCKWASHER	SG4265
71	00-671-171-523	SPLIT PIN HOLLOW	SG4265
72	17-203-277-001	UPPER COUNTERWEIGHT SPLASH RING	SG4265
73	00-615-086-546	CAPSCREW FLAT HEAD	SG4265
74	17-201-512-001	DUST COLLAR GASKET	SG4265
75	17-300-396-001	STUD	SG4265
76	00-631-001-116	HEX NUT	SG4265
77	00-651-001-490	WASHER	SG4265
78	00-631-141-116	HEX JAMNUT	SG4265
79	07-146-694-008	BOLT SQ.HD	SG4265
80	00-631-041-148	HEAVY HE NUT	SG4265
81	00-631-161-148	HEAVY HEX JAMNUT	SG4265
82	17-202-783-501	AIR INLE CONNECTOR ASSEMBLY	SG4265
83	17-402-791-401	ECCENTRI ASSEMBLY PIX	SG4265
84	17-402-789-506	ECCENTRI ASSEMBLY	SG4265
85	17-302-945-001	ECCENTRI MKII	SG4265
86	17-401-227-001	ECCENTRIC BUSHING	SG4265
87	17-203-275-501	UPPER COUNTERWEIGHT ASSEMBLY	SG4265
88	00-615-138-658	CAPSCREW HEX SOCKET NYLOK	SG4265
89	17-402-788-001	UPPER COUNTERWEIGHT	SG4265
90	00-615-138-561	CAPSCREW HEX SOCKET NYLOK	SG4265
91	17-303-595-001	UPPER COUNTERWEIGHT RETAINER RING	SG4265
92	17-302-957-001	LOWER COUNTERWEIGHT	SG4265
93	00-615-142-669	CAPSCREW HE SOCKET	SG4265
94	00-651-016-411	WASHER	SG4265
95	00-671-115-583	DOWEL PIN	SG4265
96	07-246-281-001	KEY ECCENTRI BUSHING	SG4265
97	17-302-958-001	ECCENTRIC GEAR MKII	SG4265
98	07-145-539-001	KEY,ECCENTRIC GEAR	SG4265
99	00-615-142-611	CAPSCREW HEX SOCKET	SG4265
100	07-345-013-001	ECCENTRIC WEARING RING	SG4265
101	17-303-084-001	ECCENTRIC SUPPOR RING	SG4265
102	00-615-142-724	CAPSCRE HEX SOCKET	SG4265
103	00-655-009-052	LOCKWASHER	SG4265
104	17-201-787-055	O-RING	SG4265
105	17-303-562-503	MPS CYLINDER W/SHIP COVERS	SG4265
106	17-402-757-401	MPS CYLINDER INSTALL PIX	SG4265
107	17-501-860-503	MPS CYLINDER W/POSITION INDICATOR ASM	SG4265
108	17-300-182-501	MPS CYLINDER	SG4265
109	17-300-396-002	STUD	SG4265
110	00-631-041-128	HEAVY HEX NUT	SG4265
111	00-631-161-128	HEAVY HEX JAMNUT	SG4265
112	17-302-899-001	MPS CYLINDER BUSHING -LOWER	SG4265
113	07-250-231-501	MPS CYLINDER BUSHING -UPPER	SG4265
114	00-615-142-651	CAPSCREW HEX SOCKET	SG4265
115	00-615-138-651	CAPSCREW HEX SOCKET NYLON	SG4265
116	00-671-171-523	SPLIT PIN HOLLOW	SG4265
117	00-711-497-016	PIPE PLUG SQ.HD	SG4265
118	17-201-787-035	O-RING	SG4265
119	17-402-244-501	PISTON AND PLUG ASSEMBLY	SG4265
120	17-202-759-001	PISTON PLUG	SG4265
121	00-615-142-613	CAPSCREW HEX SOCKET	SG4265
122	00-711-533-008	PIPE PLUG CI	SG4265
123	00-671-117-877	DOWEL PIN	SG4265
124	17-303-539-501	PISTON WEAR PLATE ASSEMBLY	SG4265
125	17-104-616-001	STEP WASHER RETAINER	SG4265
126	00-673-165-300	RETAINING RING, EXTERNAL	SG4265
127	07-252-540-001	STEP WASHER	SG4265
128	17-103-679-003	MPS SEAL W/O FILLER	SG4265
129	17-302-963-001	CLAMP PLATE	SG4265
130	17-202-782-001	SEAL RETAINER RING	SG4265
131	00-615-142-468	CAPSCREW HEX SOCKET	SG4265
132	00-655-009-032	LOCKWASHER	SG4265
133	17-303-650-001	HOLDER -MEASURING TUBE	SG4265
134	65-965-027-002	GASKET-TAPERED	SG4265
135	17-107-498-001	PLUG,POSITION INDICATOR MEASURING TUBE	SG4265
136	65-751-536-006	O-RING	SG4265
137	17-203-309-001	PLUG-MEASURING TUBE	SG4265
138	29300219	DECAL-RESPIRATOR	SG4265
139	26-205-880-001	WARNING SIGN -GUARD IN	SG4265
140	26-206-910-001	WARNING SIGN -LIFTING	SG4265
141	26-206-911-001	WARNING SIGN -LOCKOUT	SG4265
142	26-206-912-001	WARNING SIGN -STAND CLEAR	SG4265
143	17-402-218-501	MPS CYLINDER COVER PLATE ASSEMBLY	SG4265
144	00-751-531-474	O-RING	SG4265
145	65-615-145-079	CAPSCREW SOCKET	SG4265
146	17-201-249-003	BOLT SQ.HEAD	SG4265
147	00-631-041-128	HEAVY HEX NUT	SG4265
148	00-631-161-128	HEAVY HEX JAMNUT	SG4265
149	00-711-509-006	PIPE PLUG	SG4265
150	17-107-495-004	POSITION TRANSDUCER 400MM WI TUBE	SG4265
151	00-615-142-548	CAPSCREW HEX SOCKET	SG4265
152	65-655-022-007	SPRING WASHER	SG4265
153	00-711-087-052	PIPE BUSHING CI	SG4265
154	65-751-532-026	O-RING	SG4265
155	17-106-891-002	MPS SHIPPING COVER PLATE GUARD	SG4265
156	17-107-040-510	CABLE ASSEMBLY	SG4265
157	17-203-302-001	POSITION TRANSDUCER ADAPTER	SG4265
158	65-751-532-091	O-RING	SG4265
159	65-615-146-304	CAPSCREW SOCKET	SG4265
160	17-402-904-505	ENGLISH	SG4265

In industries like mining and building materials, crushers are crucial equipment. Jaw crushers and cone crushers, both commonly used crushing equipment, each offer unique advantages and applications. Many people struggle to choose between them. Below, we analyze their pros and cons for your reference.

 

Differences in Working Principles

 

The working principle of a jaw crusher is quite unique. Its crushing chamber consists of a fixed jaw plate and a movable jaw plate. The eccentric motion of the eccentric shaft drives the movable jaw plate in cyclical motion against the fixed jaw plate. When the jaw plates move closer together, the squeezing force crushes the material; when the movable jaw plates move further apart, the crushed material slides down and out. This simulation is ideal for coarse crushing of large, bulky materials and is typically used as the first step in ore crushing.

 

 

The working principle of a cone crusher is different. A motor drives a drive shaft, which in turn drives the main shaft, which rotates the eccentric assembly. The head assembly, driven by the eccentric assembly, oscillates back and forth, sometimes approaching and sometimes moving away from the bowl assembly. During this process, the material is subjected to repeated compression and impact, and only qualified material falls out of the crushing chamber. This continuous crushing method makes it excellent for both secondary and tertiary crushing, and is typically used as a secondary process in ore crushing.

Performance Comparison

 

Jaw Crusher

High Reduction Ratio: Capable of crushing large bulk materials to medium or smaller particle sizes in a single operation, offering excellent coarse crushing capabilities.

Simple Structure: Easy maintenance and low operating costs. Large Feed Size: Can handle larger feed materials

Cone Crusher

High Production Efficiency: Deep crushing chamber allows for high throughput per unit time, resulting in relatively high output.

High Finished Product Size: The finished product has a more uniform particle size and slightly better shaping, making it particularly suitable for applications requiring high finished product size.

 

 

Jaw crushers and cone crushers have their own advantages and disadvantages. There is no absolute good or bad. The key is to choose the crusher that suits you best based on comprehensive considerations of your own production needs, material properties, budget and other factors to achieve the best economic benefits and production efficiency in production.

Telsmith cone crusher parts mainly divided into two parts. Wear and spare parts.

 

Wear Parts

 

These are the parts that directly interact with the rock and wear out most frequently. 

 

1. Mantle: It's mounted on the main shaft.

2. Bowl Liner (Cone Crusher Concave): The rock is crushed between the mantle and the bowl liner.

3. Feed Plate (mantle nut cap): Sits at the top of the crusher, just under the feed hopper. 

4. Torch Ring: A sacrificial ring that sits at the top of the crusher. It protects the head and mainframe from damage caused by welding during liner changes or from extreme wear.

 

Mechanical & Hydraulic System Parts

 

These parts are responsible for the crusher's movement, adjustment, and protection.

 

1. Main Shaft: It transmits the gyrating motion from the eccentric assembly.

2. Eccentric Assembly: It consists of an inner eccentric bushing and an outer eccentric bushing. 

3. Head & Main Shaft Assembly: This is the assembly that includes the main shaft, crusher mantle, and other components that actually gyrate.

4. Hydraulic Cylinders: Used to adjust the crusher's closed-side setting (CSS) for product size control and to provide overload protection (e.g., tramp iron relief). If uncrushable material enters, the hydraulic system allows the cylinder to lower, letting the material pass, and then returns to the original setting.

5. Clamping Cylinder: Holds the adjustment ring in place to maintain the CSS.

6. Springs or Accumulators: In some models, these provide the return force for the tramp relief system.

 

You can contact us to know more about Telsmith parts. Here are some main part numbers for Telsmith as follows:

No	Part Number	Description	Crusher Model
1	1050641	GENERAL ARRANGEMENT	38SBS
2	1070426	OIL LUBE ARRANGEMENT	38SBS
3	1046125	BASE UNIT	38SBS
4	1062797	FLYWHEEL	38SBS
5	1070219	UPPER FRAME	38SBS
6	1050163	POWER ROTATE SYSTEM	38SBS
7	1055854	POWER ROTATE SENSOR ASSY	38SBS
8	PN-0543	PAINT, PRIMER, GRAY	38SBS
9	VLX-20331-01	PAINT, ASTEC BEIGE ACRYLIC	38SBS
10	1082546	MANGANESE, S-XC	38SBS
11	1082547	MANGANESE, S-C	38SBS
12	1082548	MANGANESE, S-M	38SBS
13	1082549	MANGANESE, FC-C	38SBS
14	1082550	MANGANESE, FC-M	38SBS
15	1082551	MANGANESE, FC-F	38SBS
16	1097430	PWRUNIT, HYD	38SBS
17	C1-272-1545B	OIL HEATING UNIT	38SBS
18	1052978	HOSES, CONN, RELIEF & LOCK	38SBS
19	1019895	HOSES,CONN., POWER ROTATE	38SBS
20	1017754	BOTTOM PLATE W/O ANTI-SPIN	38SBS
21	1045259	ANTI-SPIN	38SBS
22	Y-272-2600B	HOSES,CONN., ANTI-SPIN	38SBS
23	1060709	OIL TANK ASSEMBLY	38SBS
24	C1-272-1545B	OIL HEATING UNIT	38SBS
25	1096315	OIL PUMP ASSY	38SBS
26	1071761	COOLER ASSY	38SBS
27	1062281	UNIVERSAL FLOWMETER	38SBS
28	A-272-2643	COUNTERSHAFT BOX	38SBS
29	23G39	FTG,NPT,HOL HEX PLUG	38SBS
30	12B38	HHCS	38SBS
31	10S89	CHW	38SBS
32	BA-272-2443	COUNTERSHAFT	38SBS
33	30H22	BEARING CONE	38SBS
34	30H21	BEARING CUP	38SBS
35	DB-272-2443	OIL GUARD	38SBS
36	63L64	OIL SEAL	38SBS
37	2.60E+29	HHCS	38SBS
38	B1-18-1167	BEVEL PINION	38SBS
39	CA-272-2443	SHIM	38SBS
40	CB-272-2443	SHIM	38SBS
41	CC-272-2443	SHIM	38SBS
42	CD-272-2443	SHIM	38SBS
43	27S97	AIR BREATHER	38SBS
44	23B25	PIPE CPLG	38SBS
45	16G29	PIPE SEALANT	38SBS
46	HA1-272-2438W	BOTTOM PLATE	38SBS
47	16V75	HHCS	38SBS
48	26K68	HHCS	38SBS
49	26B48	CHW	38SBS
50	11T02	SILICONE SEALANT	38SBS
51	23D16	PLUG,PIPE	38SBS
52	23D24	PLUG	38SBS
53	AA-272-2632	TAPER HEAD	38SBS
54	A1-272-2634	MAIN SHAFT	38SBS
55	62D12	QCOUPLING,HYD,ST OR,FML	38SBS
56	62D14	QCOUPLING,HYD,PLUG	38SBS
57	62D13	QCOUPLING,HYD,ST OR,MALE	38SBS
58	62D15	QCOUPLING,HYD,CAP	38SBS
59	23H54	FTG,HYD,JIC,ST CON	38SBS
60	H0823-08082225-348	HOSE ASSY	38SBS
61	A-272-2636	ECCENTRIC	38SBS
62	TA-272-2438	SLEEVE,INNER	38SBS
63	1.20E+53	BABBITT	38SBS
64	10S47	THRUST ROLLER BEARING	38SBS
65	A-272-2637	ROTARY SEAL RING	38SBS
66	EH-17-26	PIN	38SBS
67	13B22	SHCS	38SBS
68	26C24	SHCS	38SBS
69	CA-272-2637	PISTON RING	38SBS
70	10P71	BAKELITE	38SBS
71	20N72	SHELLAC	38SBS
72	BA-272-2637	ROTARY SEAL RING WEIGHT	38SBS
73	12R84	HHCS	38SBS
74	10T77	THREADLOCKER,LOCTITE	38SBS
75	26B48	CHW	38SBS
76	CH-17-26	PIN	38SBS
77	DA-272-2677	ANTI SPIN DRIVE TANG	38SBS
78	26B93	SHCS	38SBS
79	10T77	THREADLOCKER	38SBS
80	EA-272-2677	ANTI SPIN SLIDER PLATE, BREVINI	38SBS
81	1025117	ANTI-SPIN ADAPTER PLATE	38SBS
82	6.40E+83	SHCS	38SBS
83	10H50	THREADLOCKER	38SBS
84	62B78	GEARBOX	38SBS
85	1043735	BOTTOM PLATE	38SBS
86	23D21	PLUG	38SBS
87	6.40E+88	SHCS	38SBS
88	6.40E+85	CHW	38SBS
89	26B48	CHW	38SBS
90	16V75	HHCS	38SBS
91	23D24	PLUG	38SBS
92	16G29	PIPE SEALANT	38SBS
93	23C20	FTG,HYD,JIC,NPT	38SBS
94	12W73	FTG,HYD	38SBS
95	10D98	FTG,HYD,JIC,BH UN EL	38SBS
96	62A01	MOTOR,HYD	38SBS
97	64B98	ADHESIVE,LOCTITE	38SBS
98	12L83	SHCS	38SBS
99	23P61	HYD	38SBS
100	15X33	HYD,JIC	38SBS
101	62D34	HYD,JIC,REDUCER	38SBS
102	1025148	GEARBOX COVER,ANTI-SPIN	38SBS
103	23V93	HHCS	38SBS
104	1045260	ANTI-SPIN HYDRAULICS	38SBS
105	H0423-06062225-016	HOSE ASSY	38SBS
106	26J03	FTG,HYD,JIC,SN	38SBS
107	23R04	FTG,HYD,JIC,ST CON	38SBS
108	62B80	MANIFOLD ASSY	38SBS
109	27V34	HHCS	38SBS
110	23H53	FTG,HYD,JIC,ST	38SBS
111	26J25	FTG,HYD,JIC,SN EL	38SBS
112	H1023-10102222-091	HOSE ASSY	38SBS
113	H1023-10102222-083	HOSE ASSY	38SBS
114	62H69	FTG,HYD,ST OR,RED/EXP	38SBS
115	62D33	FTG,HYD,JIC,ST RUN TEE	38SBS
116	12T24	FTG,HYD,JIC,CAP	38SBS
117	H0423-06062222-085	HOSE ASSY	38SBS
118	H0423-06062222-058	HOSE ASSY	38SBS
119	23P61	FTG,HYD,JIC,ST EL	38SBS
120	61D15	FTG,HYD,JIC,ST CON-SN	38SBS
121	62D09	QCOUPLING,HYD,ST OR,MALE	38SBS
122	62D11	QCOUPLING,HYD,PLUG/CAP	38SBS
123	62D50	CLAMP SET,TWIN	38SBS
124	62D51	CLAMP,COVER PLATE,TWIN	38SBS
125	20X16	HHCS	38SBS
126	62D47	CLAMP SET,TWIN	38SBS
127	62D48	CLAMP,COVER PLATE,TWIN	38SBS
128	15C82	HHCS	38SBS
129	11P81	CABLE TIE	38SBS
130	1032745	MAIN FRAME	38SBS
131	62A30	BEARING SPHERICAL PLAIN	38SBS
132	64M05	RETAINING RING,INTERNAL	38SBS
133	AB-272-2633	THRUST PIN BUSHING	38SBS
134	31A41	RETAINING RING	38SBS
135	EA-272-2633	SLEEVE,OUTER	38SBS
136	A-272-448	OUTER SNAP RING	38SBS
137	1.20E+53	BABBITT	38SBS
138	BD-272-2603	FRAME ARM SHIELD	38SBS
139	EB-272-2403	COUNTERSHAFT BOX SHIELD	38SBS
140	CD-272-2603	COUNTERSHAFT BOX SHIELD	38SBS
141	10P71	BAKELITE	38SBS
142	20N72	SHELLAC	38SBS
143	10S47	THRUST ROLLER BEARING	38SBS
144	BA-272-2636	BEVEL GEAR	38SBS
145	12K10	HHCS	38SBS
146	B-272-337	SHIM	38SBS
147	CA-272-2636	SHIM	38SBS
148	D-272-337	SHIM	38SBS
149	CB-272-2636	SHIM	38SBS
150	13B33	SHCS	38SBS
151	A-272-447	PISTON RING-INNER	38SBS
152	1024721	ECCENTRIC ASSY	38SBS
153	1019753	HEAD & SHAFT ASSY	38SBS
154	1017592	C'SHAFT BOX ASSY	38SBS
155	1046127	BASE UNIT HYDRAULICS	38SBS
156	CL-272-2603	SUPPORT BRACKET	38SBS
157	60N51	GROMMET,RUBBER	38SBS
158	27W63	MULTI-CLAMP ASSY	38SBS
159	1.00E+11	HHCS	38SBS
160	23F36	PIPE TEE	38SBS
161	10Z99	RED. BUSH	38SBS
162	23R63	FTG,HYD,JIC,NPT,M CON	38SBS
163	60K80	FTG,HYD,JIC,CAP	38SBS
164	23L53	FTG,HYD,JIC,NPT,M EL	38SBS
165	H0623-06062222-091	HOSE ASSY	38SBS
166	62D90	CLAMP SET, HVY, SNGL	38SBS
167	62D91	COVER PLATE, FOR HOSE CLAMP	38SBS
168	13M81	HHCS	38SBS
169	61N38	FTG,HYD,JIC,SN BR TEE	38SBS
170	23P62	FTG,HYD,JIC,NPT,M CON	38SBS
171	16G29	PIPE SEALANT	38SBS
172	12T24	FTG,HYD,JIC,CAP	38SBS
173	65F75	CYL ASM,HYD	38SBS
174	27L09	SHSS	38SBS
175	C-272-395	PLUG,BRASS	38SBS
176	BE-17-575	HHCS	38SBS
177	10H53	ANTI-SEIZE&LUB.COMP	38SBS
178	H1223-12124040-020	HOSE ASSY	38SBS
179	H1223-12124040-023	HOSE ASSY	38SBS
180	H1223-12124040-018	HOSE ASSY	38SBS

The main parts of a Sandvik VSI (Vertical Shaft Impactor) crusher can be grouped into the following key assemblies and wear components:

 

1. Rock Crusher Wear Parts Rotor Assembly  

- Rotor body – bare rotor in various sizes (500, 690, 760, 840, 990 mm)  

- Rotor top plate / taper-lock – secures the rotor to the shaft  

 

2. Customized VSI Crusher Wear Parts Feed System  

- Feed tube – guides material into the rotor  

- Feed eye ring – centralises the feed stream and protects the tube  

 

3. Customized VSI Crusher Wear Parts Components Wear Liners & Distributor  

- Distributor plate*(flat or cone, hi-chrome) – spreads feed evenly inside the rotor  

- Upper & lower wear plate sets – protect rotor inner walls  

- Top wear plate set – shields the rotor top  

- Cavity wear plate sets – line the crushing chamber around the rotor  

 

4. Sandvik Impact Wear Parts Tip & Trail Components  

- Rotor tips / tip sets – tungsten-carbide or alloy inserts that impart energy to the rock  

- Back-up tips – secondary protection behind the main tips  

• Trail plates (wide, narrow, straight, tungsten-edged) – guide material flow and reduce wear  

 

361	840.0044-00	Screw	CV218
362	847.0059-00	Washer	CV218
363	488.0294-001	Bolt	CV218
364	853.0997-00	Clips R-Clips Type A E4	CV218
365	488.0113-901	Standard	CV218
366	488.0113-902	High Temperature	CV218
367	853.0603-00	Pin Prym N 10X28	CV218
368	841.0416-00	Screw	CV218
369	488.0297-001	Top Key	CV218
370	840.0657-00	Screw	CV218
371	847.0132-00	Washer Brb 21X36	CV218
372	845.0203-00	Nut Lock	CV218
373	840.0073-00	Screw	CV218
374	847.0036-00	Spring Washer Fbb 16.2	CV218
375	488.0299-001	Bottom Key	CV218
376	488.008-01	Base	CV218
377	488.0109-001	Discharge Plate	CV218
378	488.0141-001	Liners	CV218
379	488.0318-001	Liners	CV218
380	488.0315-001	Gusset Wear Casting	CV218
381	488.0505-001	Vibration Damper	CV218
382	847.0147-00	Washer	CV218
383	847.0124-00	Washer	CV218
384	845.0387-00	Nut Lock	CV218
385	840.0678-00	Screw	CV218
386	840.0049-00	Screw	CV218
387	845.0030-00	Nut Lock	CV218
388	853.0997-00	Clips R-Clips Type A E4	CV218
389	847.0132-00	Washer	CV218
390	845.0203-00	Nut Lock	CV218
391	840.0532-00	Screw	CV218
392	488.0288-901	Cover	CV218
393	840.0076-00	Screw	CV218
394	488.0286-001	Perforated Plate	CV218
395	847.0144-00	Washer	CV218
396	840.0033-00	Screw	CV218
397	847.0016-00	Washer	CV218
398	840.0070-00	Screw	CV218
399	845.0215-00	Nut Lock	CV218
400	840.0064-00	Screw	CV218
401	984.1159-00	Pre Start Sounder Kit	CV218
402	984.1160-00	Vibration Protection	CV218
403	843.1579-00	Screw	CV218
404	900.1139-00	Clip Rsgu 1.22/15	CV218
405	840.0014-00	Screw	CV218
406	845.0217-00	Nut Lock	CV218
407	488.0314-901	Grease Duct	CV218
408	488.0313-001	Grease Chute	CV218
409	488.1311-901	Wedge	CV218
410	840.0069-00	Screw	CV218
411	840.0622-00	Screw	CV218
412	488.1676-001	Ring	CV218
413	488.1673-901	Vsi Feed Kit Assembly	CV218
414	485.0258-001	Feed Tube	CV218
415	488.0270-001	Wedge	CV218
416	488.1677-901	Plate	CV218
417	845.0010-00	Nut Lock	CV218
418	488.0499-901	Chain Hlz 5.5Mm Sms 1507	CV218
419	840.0078-00	Screw	CV218
420	840.0653-00	Screw	CV218
421	488.1679-901	Hatch	CV218
422	488.1624-901	Locking Plate	CV218
423	488.1671-001	Bolt	CV218
424	845.0203-00	Nut Lock	CV218
425	488.0219-901	High Profile Rotor Body	CV218
426	488.0029-001	Taper Lock	CV218
427	488.0361-901	Lower Wear Plate Set	CV218
428	488.0360-901	Upper Wear Plate Set	CV218
429	488.0076-001	Distributor Plate	CV218
430	488.1513-901	Distributor Locating Pin Set	CV218
431	488.1644-901	Cavity Wear Plate Set Turbo (Upper)	CV218
432	488.1703-901	Cavity Wear Plate Set Turbo (Middle)	CV218
433	488.1704-901	Cavity Wear Plate Set Turbo (Lower)	CV218
434	488.0362-901	Trail Plate 330 Set	CV218
435	488.1456-901	Turbo Tip Set 110 Mm (Hard)	CV218
436	488.0368-901	Backup Tip Set	CV218
437	488.0369-901	Top Wear Plate Set	CV218
438	840.0077-00	Screw	CV218
439	841.0502-00	Screw	CV218
440	488.0841-001	Top Plate	CV218
441	488.0017-901	Roof	CV218
442	488.0031-901	Hopper	CV218
443	488.0104-901	Trottle	CV218
444	488.0282-901	Cover	CV218
445	488.0083-001	Plate D=340	CV218
446	488.0165-001	Cover	CV218
447	488.0293-001	Bolt	CV218
448	488.0292-001	Bolt	CV218
449	853.0997-00	Clips R-Clips Typ W E4	CV218
450	488.0484-001	Plate D=280	CV218
451	488.0485-001	Plate D=220	CV218
452	840.0622-00	Screw	CV218
453	488.1325-001	Gasket	CV218
454	488.1326-001	Cover	CV218
455	840.0020-00	Screw	CV218
456	847.0012-00	Washer	CV218
457	488.0147-901	Protection	CV218
458	488.0429-901	Cover	CV218
459	488.0285-001	Perforated Plate	CV218
460	840.0033-00	Screw	CV218
461	847.0144-00	Washer	CV218
462	840.0037-00	Screw	CV218
463	845.0213-00	Nut Lock	CV218
464	488.0500-001	Edge List	CV218
465	914.0206-00	Grease Unit Keg Mounted	CV218
466	825.0148-00	Grease Firetemp Xt2	CV218
467	825.0143-00	Grease Long Time Pd2	CV218
468	904.0545-00	Grease Hose L=600	CV218
469	904.0543-00	Grease Hose L=1280	CV218
470	904.0542-00	Grease Hose L=550	CV218
471	902.1104-00	Valve Distributor	CV218
472	902.1105-00	Cycle Indicator For Valve Distributor 2	CV218
473	906.0478-00	Hand Pump Gla-25-4L	CV218
474	912.0214-00	Return Filter Mf-Bn-80-Ga-010-E1	CV218
475	902.0947-00	Pump Valve Hdm11S/3K04150Aaa03L100	CV218
476	908.0471-00	Cylinder 25Ca-R50/30-200/85	CV218
477	908.0470-00	Cylinder 25Ca-Vr-65/35-250/85	CV218
478	912.0213-00	Air Filter Uc-Sab-3101-R1/4	CV218
479	904.0434-00	812-06 Kl=450	CV218
480	904.0435-00	812-06 Kl=942	CV218
481	904.0436-00	812-06 Kl=1300	CV218
482	904.0439-00	812-06 Kl=640	CV218
483	904.0440-00	812-06 Kl=1570	CV218
484	488.0474-901	Hydraulic Plate	CV218
485	904.0442-00	Hose L=1950	CV218
486	904.0441-00	Hose L=900	CV218
487	881.0191-00	Bolt Interlock	CV218
488	881.0185-00	Spacer For Mlh-Q1058	CV218
489	881.0192-00	Time Delay Unit	CV218
490	881.0174-00	Sealed Key C And D	CV218
491	881.0173-00	Heavy Duty Access Interlock	CV218
492	881.0175-00	Dust Cap	CV218
493	488.1212-901	Frame	CV218
494	488.0322-901	Transport Leg	CV218
495	840.0650-00	Screw	CV218
496	845.0010-00	Nut Lock	CV218
497	847.0132-00	Washer	CV218
498	488.0196-901	Cylinder Bracket	CV218
499	840.0649-00	Screw	CV218
500	845.0203-00	Nut Lock	CV218
501	488.0294-001	Bolt	CV218
502	853.0997-00	R-Clips Type A E4	CV218
503	488.0300-901	Skid Frame	CV218
504	840.0649-00	Screw	CV218
505	845.0203-00	Nut Lock	CV218
506	847.0132-00	Washer	CV218
507	488.0107-901	Leg (1900 Mm/74.8”)	CV218
508	488.0092-901	Leg (1900 Mm/74.8”)	CV218
509	840.0650-00	Screw	CV218
510	847.0132-00	Washer	CV218
511	845.0203-00	Nut Lock	CV218
512	488.0495-901	Leg (2670 Mm/105.1”)	CV218
513	488.0496-901	Leg (2670 Mm/105.1”)	CV218
514	840.0650-00	Screw	CV218
515	847.0132-00	Washer	CV218
516	845.0203-00	Nut Lock	CV218
517	488.1381-901	Cv218 Drive Pulley	CV218
518	879.0636-00	Motor Pulley	CV218
519	488.0208-001	Crusher Pulley	CV218
520	869.0336-00	Motor Taperlock	CV218
521	869.0300-00	Motor Taperlock	CV218
522	875.0368-00	V-Belts	CV218
523	488.0445-001	Crusher Taperlock	CV218
524	840.0824-00	Crusher Taperlock Bolts	CV218
525	847.0017-00	Crusher Taperlock Washers	CV218
526	488.1377-901	Cv218 Drive Pulley	CV218
527	879.0664-00	Motor Pulley	CV218
528	488.0208-001	Crusher Pulley	CV218
529	869.0336-00	Motor Taperlock	CV218
530	869.0300-00	Motor Taperlock	CV218
531	875.0368-00	V-Belts	CV218
532	488.0445-001	Crusher Taperlock	CV218
533	840.0824-00	Crusher Taperlock Bolts	CV218
534	847.0017-00	Crusher Taperlock Washers	CV218
535	488.1380-901	Cv218 Drive Pulley	CV218
536	879.0637-00	Motor Pulley	CV218
537	488.1382-901	Cv218 Drive Pulley	CV218
538	879.0638-00	Motor Pulley	CV218
539	869.0359-00	Motor Taperlock	CV218
540	869.0351-00	Motor Taperlock	CV218

Why Packaging Design Changes Are Important for Brands

In today’s competitive market, packaging redesign isn’t just about a new look—it’s about staying relevant, boosting sales, and connecting with modern consumer values. From sustainability to smart technology, brands must evolve their packaging to stay ahead.

Old Packaging vs New Packaging: Key Drivers of Change

1. Sustainability and Eco-Friendly Packaging

Consumers demand eco-conscious solutions. Switching from hard-to-recycle plastics to compostable or recyclable materials shows commitment to the environment and boosts customer loyalty.

2. Staying Current with Competitors

Study market shelves, test competitor packaging, and adapt. Learning directly from what works for others ensures your brand stays competitive.

3. Technology and Smart Packaging

Innovations like QR codes, NFC, and active packaging extend shelf life and build deeper customer engagement.

4. Policy & Regulatory Compliance

New industry rules—such as bans on single-use plastics—require timely packaging updates to stay compliant and consumer-friendly.

What Consumers Expect from Modern Packaging

1. Personalization & Branding: Customized labels and personal touches build stronger connections.

2. Convenience & Functionality: Easy-to-open, practical designs enhance customer experience.

3. Authenticity & Storytelling: Packaging that reflects brand values and identity resonates with younger audiences.

How Brands Can Adapt to Evolving Industry Trends

Don’t wait for declining sales—be proactive. A strategic redesign refreshes your brand presence while preserving identity. Gathering outside feedback ensures your packaging resonates with real consumers.

Fulinhan Packaging: Your Partner in New Packaging Design

At Fulinhan Packaging, we help brands navigate packaging transformations—sustainability, design updates, and compliance. Our consultative approach ensures smooth transitions to packaging that is modern, functional, and future-proof.

? Ready to elevate your packaging?
Contact us today for expert design consultation and tailored solutions.

 

? Email: info@fulinhan.com
? WhatsApp:+86 18259435129
? Website: https://www.fulinhanpackaging.com/

In 2025, sustainability is no longer a trend—it has become a core requirement across the global retail and FMCG sectors. Brands are moving beyond traditional plastic and shifting toward new-generation materials that improve both environmental impact and product presentation.

 

1. Recycled Polyester (rPET) Becomes Mainstream

 

More apparel and lifestyle brands are adopting rPET materials for labels, hangtags, and packaging components. Its durability and clean surface finish make it suitable for high-volume retail products while supporting ESG commitments.

 

2. Paper-Based Packaging Upgrades

 

The industry is witnessing a shift toward thicker kraft paper, molded paper pulp, and coated paper solutions. These materials offer better structure, improved print performance, and can replace plastic trays or PVC boxes in many applications.

 

3. Bio-Based Films & Coatings Rise in Demand

 

Corn-based PLA films, water-based coatings, and biodegradable laminates are gaining popularity in cosmetic, food, and premium gift packaging. These materials provide a balance between transparency, strength, and environmental benefits.

 

4. Smarter Packaging for Better Consumer Experience

 

QR codes, variable printing, and NFC tags are being integrated into packaging to help brands build interactive customer journeys, from product authentication to recycling instructions.

 

Fulinhan’s Role

 

We provide custom packaging accessories and material solutions based on global sustainability trends—ensuring your products meet both regulatory requirements and brand expectations.

 

📩 info@fulinhan.com

 

📞 +86 182 5943 5129

We’re excited to share that another shipment has been successfully prepared and sent out to our valued client in Australia.

 

From material selection to final packaging and logistics, our team takes every detail seriously to ensure each shipment meets the highest standards of quality, consistency, and on-time delivery.

 

At Fulinhan, we believe long-term cooperation is built on reliability, communication, and shared success. We deeply appreciate all our partners who continue to choose us as their packaging and garment accessory supplier.

 

✨✨ Thank you again to our Australian client for your trust and support

 

📦 Fulinhan Packaging

Your reliable OEM & ODM partner for sustainable and custom packaging solutions.

✉️ info@fulinhan.com

 | 📞 +86 18259435129

As global awareness of environmental protection continues to rise, sustainable packaging has become a key focus for brands across industries. From retail to food and cosmetics, companies are shifting toward eco-friendly materials that reduce waste and promote recyclability.

Today’s consumers care not only about the product itself but also about how it’s packaged. Using recyclable paper, biodegradable materials, and reusable packaging helps brands build a responsible image and meet growing market expectations.

At Fulinhan, we are committed to developing eco-conscious packaging solutions that combine durability, design, and sustainability. Whether it’s recyclable boxes, paper bags, or reusable packaging, we help brands achieve both environmental goals and commercial success.

Let’s work together to build a greener and smarter packaging future.

 

📦 Fulinhan Packaging — Your reliable partner for sustainable packaging solutions.
✉️ info@fulinhan.com | 📞 +86 18259435129

In today’s competitive retail and promotional market, packaging isn’t just about holding a product—it’s about brand image, durability, and sustainability. Laminated non woven tote bags wholesale have become a go-to solution for businesses looking for eco-friendly, reusable, and custom-branded packaging. But what happens when these bags don’t perform as expected?

From broken handles and peeling lamination to customer complaints and brand damage, a poorly made tote bag can create serious challenges for your business. As a senior packaging solutions supplier, Fulinhan has seen firsthand the difference between high-quality custom printed laminated non woven bags and those that fail under pressure.

In this blog, we’ll explore why laminated non woven tote bags sometimes fail, the most common problems, and how to prevent them with the right materials, equipment, and expertise.

What Laminated Non Woven Tote Bags Are Designed to Do

Laminated non woven tote bags combine the strength of polypropylene fabric with a thin laminated coating. This lamination provides water resistance, smooth print surfaces, and extended durability. Ideally, these reusable shopping bags are designed to:

1. Carry heavy loads without tearing

2. Resist water, moisture, and stains

3. Showcase vibrant, custom printed logos for brand visibility

4. Be reused multiple times, reducing waste and promoting sustainability

When done right, laminated non woven tote bags can enhance both customer satisfaction and brand recognition.

Why Tote Bags Fail: Common Causes

Even though custom laminated tote bags wholesale look simple, the production process requires precision. Here are the most common causes of failure:

1. Weak Handles & Stitching

If the handle material or stitching isn’t reinforced, the bag can break under weight. Customers often complain about handles tearing after just a few uses.

2. Poor Lamination Quality

Low-grade lamination can peel, bubble, or crack, especially when exposed to heat, sunlight, or heavy use. This not only ruins the appearance of the bag but also shortens its lifespan.

3. Inconsistent Fabric Quality

Not all non woven fabric is the same. Bags made with thinner, low-density polypropylene can feel flimsy and tear more easily.

4. Misaligned Printing or Fading Designs

A tote bag is not just functional—it’s a walking advertisement for your brand. If the printing fades, scratches, or peels, your custom laminated non woven tote bags lose their promotional value.

The Real Impact of Tote Bag Failure

When laminated non woven shopping bags fail, the consequences affect both products and business reputation.

Product Consequences:

1. Bags tear, leak, or collapse when carrying items

2. Branding and logos fade, reducing visibility

3. Customers stop reusing the bags, cutting down brand exposure

Business Consequences:

1. Negative customer feedback on durability

2. Extra costs from returns, replacements, or rush re-orders

3. Brand reputation damage when customers perceive your packaging as cheap or unreliable

Fulinhan’s One-Stop Packaging Solution

At Fulinhan, we take an engineering-first and customer-focused approach to packaging. With years of expertise in garment accessories and packaging, we deliver durable, sustainable, and brand-focused laminated non woven tote bags wholesale that meet your exact requirements.

Our advantages include:

1. Material expertise: We source and test non woven fabrics to ensure consistency and strength.

2. Advanced equipment: High-precision lamination and printing machines deliver smooth, long-lasting finishes.

3. Custom branding: Custom printed laminated non woven tote bags with full-color or single-color options tailored to your brand identity.

4. Sustainable solutions: Designed to be reusable shopping bags that support eco-friendly initiatives.

5. One-stop service: From design consultation to sampling, mass production, and logistics, we handle the entire packaging pipeline.

Partner with a Supplier That Understands Your Needs

If you’re a retailer, CPG brand, or promotional company looking for laminated non woven tote bags wholesale, Fulinhan is here to help. We don’t just supply packaging—we engineer solutions that protect your products, strengthen your brand, and delight your customers.

? Ready to place your order?
Contact us today to get a quote for your laminated non woven tote bags wholesale project.

✉️ Email: info@fulinhan.com
? Phone: +86 18259435129

? Let Fulinhan help you create durable, sustainable, and brand-focused packaging solutions that your customers will love to reuse.

In today’s competitive retail environment, packaging is more than protection — it’s communication. The right custom packaging design can turn an ordinary product into a memorable brand experience.

Modern consumers pay attention to details — colors, textures, finishes, and sustainability all influence how they perceive a brand. Custom packaging helps retail brands:

• Strengthen brand identity with consistent visual elements

• Enhance customer experience through premium and thoughtful design

• Increase perceived value, making products stand out on crowded shelves

• Reflect sustainability values with eco-friendly materials and smart structure design

For retail and DTC brands, investing in custom printed packaging boxes, reusable bags, and branded accessories is not just about aesthetics — it’s a strategic move that drives sales and brand loyalty.

At Fulinhan Packaging, we help brands bring their packaging vision to life through tailored design, high-quality materials, and advanced printing technology. Our solutions blend creativity, functionality, and sustainability to ensure your packaging tells your brand’s story — beautifully.

 

📦 Fulinhan Packaging — Custom OEM & ODM Packaging for Retail and Lifestyle Brands.
✉️ info@fulinhan.com | 📞 +86 18259435129